PV7-1X/06-10RA01MA3-05
PV7-2X/20-25RA01MA0-10
PV7-1X/06-10RA01MA3-10 German Rexroth imported hydraulic oil pump blade pump in stock
| Parameter | Specification |
| Model Series | PV7-1X/10-14RE01MC0-16, PV7-1X/16-20RE01MC0-16, PV7-2X/20-25RE01MC0-16 (typical models) |
| Displacement per Revolution | 10–25 cm³/rev (varies by specific model) |
| Maximum Operating Pressure | 210 bar (continuous), 250 bar (peak) |
| Maximum Speed | 1800–3600 rpm (depends on displacement and fluid viscosity) |
| Minimum Speed | 600 rpm (ensures stable operation) |
| Fluid Medium | Mineral oil-based hydraulic fluid (ISO VG 32/46/68 recommended) |
| Fluid Temperature Range | -20 °C to +80 °C (operation); -40 °C to +90 °C (storage) |
| Viscosity Range | 10–1000 mm²/s (operation); 2–1500 mm²/s (start-up) |
| Volumetric Efficiency | ≥90% (at rated pressure and speed) |
| Total Efficiency | ≥80% (at rated working condition) |
| Noise Level | ≤65 dB(A) (at 1 m distance under rated operation) |
| Suction Pressure | -0.8 bar to +1 bar (absolute pressure: 0.2–1.1 bar) |
| Mounting Type | Flange mounting (ISO 3019-2 standard), foot mounting (optional) |
| Shaft Connection | Splined shaft (ISO 4162 standard) or keyed shaft (customizable) |
| Seal Type | Viton® or NBR shaft seals (resistant to high temperature and oil) |
| Inlet/Outlet Port | BSPP, BSPT or SAE thread (port size matches displacement) |
| Weight | 8–15 kg (varies by model and configuration) |

| PV7-2X/20-25RE01MA3-05 |
| PV7-1X/06-10RG01MA0-10 |
| PV7-2X/20-25RE01MA3-10 |
| PV7-1X/06-10RG01MA3-10 |
| PV7-1X/06-14RE01MA3-07 |
| PV7-1X/06-14RA01MA0-04 |
| PV7-1X/06-14RG01MA0-07 |
| PV7-1X/06-14RA01MA0-07 |
| PV7-2X/20-20RA01MA0-05 |
| PV7-1X/06-14RA01MA3-04 |
| PV7-2X/20-20RA01MA0-10 |
| PV7-1X/06-14RA01MA3-07 |
| PV7-2X/20-20RA01MA3-05 |
| PV7-1X/06-14RE01MA0-04 |
| PV7-2X/20-20RA01MA3-10 |
| PV7-1X/06-14RE01MA0-07 |
| PV7-2X/20-20RE01KA0-10 |
| PV7-1X/06-14RE01MA3-04 |
| PV7-1X/06-10RA01MA0-05-P50 |
| PV7-2X/20-20RA01MA0-10-P85 |
| PV7-1X/06-10RA01MA0-10-P50 |
| PV7-2X/20-25RA01MA0-05-P32 |
| PV7-1X/06-14RA01MA0-07-P50 |
| PV7-2X/20-25RA01MA0-05-P50 |
| PV7-1X/06-14RA01MA0-07-P65 |
| PV7-1X/06-14RA01MA0-07-P70 |
| PV7-2X/20-20RA01MA0-10-P65 |
| PV7-2X/20-20RA01MA0-05-P25 |
| PV7-2X/20-20RA01MA0-05-P50 |
| PV7-1X/06-14RA01MA0-10-A473 |
| PV7-1X/06-10RA01MA0-10-P100 |
| PV7-1X/06-14RA01MA0-10-A492 |
| PV7-2X/20-20RA01MA0-10-C3.1 |
| PV7-2X/20-20RA01MA0-05-A480 |
| PV7-2X/20-20RA01MA0-10-A480 |
| PV7-1X/06-10RA01MA0-10-C3.1 |
| PV7-2X/20-20RA01MA0-10-P100 |
| PV7-2X/20-25RA01MA0-05-P24Q30 |
| PV7-1X/06-10RA01MA0-05-P35Q11 |
| PV7-2X/20-25RA01MA0-05-P30Q25 |
| PV7-1X/06-10RA01MA0-05-P40Q11 |
| PV7-2X/20-25RA01MA0-05-P30Q36 |
| PV7-1X/06-10RA01MA0-05-P50Q15 |
| PV7-2X/20-25RA01MA0-05-P45Q35 |
| PV7-1X/06-10RA01MA0-10-P55Q12 |
| PV7-2X/20-25RA01MA0-05-P45Q36 |
| PV7-1X/06-10RA01MA0-10-P65Q12 |
| PV7-2X/20-25RA01MA0-10-P63Q35 |
| PV7-1X/06-10RA01MA0-10-P70Q12 |
FAQ:
1. What thread standards are available for PV7 pump ports?
BSPP, BSPT, or SAE threads (port size matches displacement).
2. How to check for leaks in PV7 pump pipe connections?
Inject 0.5-1MPa compressed air into the system and apply soapy water to seals; check for bubbles.
3. Can the PV7 pump’s rotation direction be reversed?
No, reverse rotation causes blade jamming and seal damage; verify with the nameplate arrow before startup.
4. How to verify the motor rotation direction for the PV7 pump?
Use "jogging" (1-2 seconds of power supply) to observe rotation; adjust wiring if reversed.
5. What is the requirement for the PV7 pump’s drain line?
The case drain line must be routed below the tank liquid level to ensure smooth oil return; do not reuse drain oil for suction.