The RTY Series and RTP Series Hall-effect Rotary Position Sensors offer non-contact sensing for demanding transportation and industrial environments at a competitive price. The RTY Series features integral shafts with or without levers, while the RTP Series separates the magnet from the sensor body for enhanced durability. Both series utilize Hall-effect technology to convert rotary movement into a linear output, housed in rugged, IP69K-qualified packages. They support a wide range of operating ranges and input voltages, backed by Honeywell's industry-leading R&D capabilities.
| Characteristic | RTY Series | RTP Series |
| Expected life | 35 M cycles | Infinite rotation |
| Air gap: bare magnet actuator | - | 3.00 mm 0.5 mm [0.12 in 0.02 in] |
| Air gap: housed magnet actuator | - | 2.00 mm 0.5 mm [0.08 in 0.02 in] |
| Supply voltage | LV: 5 0.5 Vdc HV: 10 Vdc to 30 Vdc | LV: 5 0.5 Vdc HV: 10 Vdc to 30 Vdc |
| Supply current (max.) | LV: 20 mA HV: 25 mA | LV: 32 mA HV: 47 mA |
| Output: standard | 0.5 Vdc to 4.5 Vdc ratiometric | 0.5 Vdc to 4.5 Vdc non-ratiometric |
| Output: inverted | 4.5 Vdc to 0.5 Vdc ratiometric | 4.5 Vdc to 0.5 Vdc non-ratiometric |
| Output signal delay | 4 ms typ. | 4 ms typ. |
| Overvoltage protection | 10 Vdc (LV) | 10 Vdc (LV) |
| Reverse polarity protection | -10 Vdc (LV) -30 Vdc (HV) | -10 Vdc (LV) -30 Vdc (HV) |
| Output to ground short circuit protection | Continuous | Continuous |
| Resolution | 12 bit | 12 bit |
| Output load resistance (pull down to ground) | 10 kOhm typ. | 10 kOhm typ. |
| EMI radiated immunity | 100 V/m per ISO11452-2 (200 MHz to 1000 MHz) | 100 V/m per ISO11452-2 (200 MHz to 1000 MHz) |
| EMI conducted immunity | 100 mA BCI per ISO11452-4 (1 MHz to 200 MHz) | 100 mA BCI per ISO11452-4 (1 MHz to 400 MHz) |
| Operating temperature range | -40 C to 125 C [-40 F to 257 F] | -40 C to 125 C [-40 F to 257 F] |
| Shock | 20 G peak (does not apply RTY Series sensor shaft with lever) | 50 G peak |
| Vibration | 20 G peak | 20 G peak |
| Salt fog concentration | 5% 1% for 240 hr per SAE J1455 | Bare magnet: 96 hr per ASTM B117 Housed magnet: 240 hr per ASTM B117 |
| Mating connector | AMP Superseal 282087-1 | AMP Superseal 282087-1 |
| Mounting screw sizes: sensor to mounting surface | Non-magnetic, stainless steel M5 screws and 10 mm [0.39 in] OD washers | Non-magnetic, stainless steel M5 screws and 10 mm [0.39 in] OD washers |
| Mounting screw sizes: housed magnet actuator to actuator mounting | - | Non-magnetic, stainless steel M4 X 0.7 screws and 8 mm [0.31 in] OD washers |
| Mounting screw sizes: shaft | Non-magnetic, stainless steel M6 screws | - |
| Mounting screw sizes: lever to mounting surface | Non-magnetic, stainless steel M3 X 0.5 plain cup point set screws | - |