MachineU > China Products
High Durability USB AM 90CB Connector with Tested Terminal Strength and Low Contact Resistance for Reliable Performance
High Durability USB AM 90CB Connector with Tested Terminal Strength and Low Contact Resistance for Reliable Performance
Specifications
length :
18.8mm
Number of Ports :
1
Supplementary Features :
-
Number of Contacts :
4P
Mounting Type :
弯插
Center Height :
-
Current Rating :
1.5A
Detection color :
白色
Voltage Rating :
30V
Operating Temperature :
-25℃~+85℃
Connector Type :
Type-A
Connect-Disconnect Life :
5千次
Gender :
公
Description :
USB-A (USB TYPE-A) Receptacle Connector 4 Position Right Angle
Mfr. Part # :
AM 90°CB
Package :
Through Hole,Right Angle
Model Number :
AM 90°CB
Description

Product Overview

This document outlines the specifications for a USB AM 90CB connector, designed for reliable performance across a wide temperature range. It details the product's electrical, mechanical, and durability characteristics, ensuring suitability for various applications.

Product Attributes

  • Brand: (SHENZHEN SHOUHAN TECHNOLOGY CO.,LTD)
  • Origin: China
  • Model: USB AM 90CB
  • Part Number: (Not specified)

Technical Specifications

ItemTest ConditionsPerformanceSpecification
CONNECTION FORCEMEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES.INSERTION FORCE0.7~4Kgf
DISCONNECTION FORCE0.7~4Kgf
TERMINAL STRENGTHA STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION. THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY. ELECTRICAL, AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED.--
CONTACT RESISTANCEMEASURED AT SMALL CURRENT (100mA OR LESS) 1000Hz-3.50m MAX
INSULATION RESISTANCEAPPLYA VOLTAGE OF 100V DC FOR 1 MIN TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED.100M MIN
DIELECTRIC STRENGTHAC 500V ims(50~60Hz)FOR 1 MIN TRIP CURRENT:0.5mA (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACL (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED. WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC.-
SOLDERABILITY TESTTHE TOP OF THE TERMINALS SHALL BE DIPPED 1mm IN THE SOLDER BATH OF 2305FOR 50.5 SECONDS. (1) SOLDER WETTING TIME SHALL BE 3 SEC OR LESS (2) THE AREA OF SOLDERING SHOULD BE OVER 75%--
RESISTANCE TO SOLDERING HEAT TESTSOLDERING IRON METHOD: BIT TEMPERATURE 3305 APPLICATION TIME OF SOLDERING IRON 30.5 SEC. HOWEVER EXCESSIVE PRESSURE SHALL NOT BE APPLIED TO THE TERMINAL. WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS. ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.HAND SOLDERINGA.350MAX., 2 sec Max
B.270MAX., 4 sec Max
HUMIDITY TESTTHE JACK SHALL BE STORED AT A TEMPERATURE OF 402 AND A HUMIDITY OF 90%TO 96% FOR 96 HR, THEN THE JACK SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HR FOR OTHER PROCEDURES. THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.--
HEAT TESTTHE JACK SHALL BE STORED AT A TEMPERATURE OF 702 FOR 96 HOURS, AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY MEASUREMENT.--
COLD TESTTHE JACK SHALL BE STORED AT A TEMPERATURE OF -253 FOR 96 HOURS AND THEN IT SHALL BE SUBJECTED TO THE CONTROLLED RECOVERY CONDITIONS FOR 1 HOUR AFTER WHICH. THERE SHALL BE NO DAMAGE ON APPEARANCE. MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.--
LIFE TESTWITHOUT LOAD: CONNECTION AND DISCONNECTION SHALL BE MADE WITH THE MATING PLUGS AND JACKS FOR 5000 CYCLES AT A SPEED OF 10 TO 25 CYCLES/MIN. LOAD: AT RATING CONDITION (NON-INDUCTIVE LOAD) CONNECTION AND DISCONNECTION SHALL BE MADE 5000 CYCLES AT A SPEED 10 TO 20 CYCLES / MIN.CONTACT RESISTANCE 0.1
DISCONNECTION FORCE0.8 TO 2.0N
OTHERMECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
TEMPERATURE CYCLING TESTTHE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES. THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.INSERTION & EXTRACTION FORCE3 TO 20N
CONTACT RESISTANCEMAX.30M
INSULATION RESISTANCEMIN.100 M
DIELECTRIC WITHSTANDING VOLTAGE100VAC/MIN (BETWEEN TERMINALS)
COLD & HEAT SHOCK TESTTHE JACK SHALL BE SUBJECTED TO 5 CYCLES OF THE FOLLOWING CONDITIONS SHOWED IN THE FIGURE, AND THEN SHALL RETURNED AND ALLOWED TO REMAIN IN ROOM AMBIENT CONDITION FOR 30 MINUTES. THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART.INSERTION & EXTRACTION FORCE3 TO 25N
CONTACT RESISTANCEMAX.30M
INSULATION RESISTANCEMIN.100 M
DIELECTRIC WITHSTANDING VOLTAGE500VAC/MIN (BETWEEN TERMINALS)

2411251528_SHOU-HAN-AM-90-CB_C6386906.pdf

Send your message to this supplier
Send Now

High Durability USB AM 90CB Connector with Tested Terminal Strength and Low Contact Resistance for Reliable Performance

Ask Latest Price
Product Detail
length :
18.8mm
Number of Ports :
1
Supplementary Features :
-
Number of Contacts :
4P
Mounting Type :
弯插
Center Height :
-
Contact Supplier
High Durability USB AM 90CB Connector with Tested Terminal Strength and Low Contact Resistance for Reliable Performance

Hefei Purple Horn E-Commerce Co., Ltd.

Verified Supplier
1 Years
anhui, hefei
Since 2009
Business Type :
Manufacturer, Distributor/Wholesaler, Agent, Importer
Main Products :
Shunts, Jumpers, Centronics Connectors, Pluggable Connector Accessories
Employee Number :
<300
Certification Level :
Verified Supplier
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products USB, DVI, HDMI Connector Assemblies
MachineU China Products
Contact Supplier
Submit Requirement