ATV32HD11N4 Schneider variable speed drive ATV32 11 kw 400 V 3 phase

Quick Details

Range of Product
Altivar 32
Product or Component Type
Variable speed drive
Product destination
Synchronous motors
Asynchronous motors
Product Specific Application
Complex machines
Function Available
-
Assembly style
With heat sink
Component name
ATV32
EMC filter
Class C2 EMC filter integrated
Phase
3 phase
[Us] rated supply voltage
380...500 V - 15...10 %
Supply voltage limits
323…550 V
Supply frequency
50...60 Hz - 5...5 %
Network Frequency
47.5...63 Hz
Motor power kW
11 kW 380...480 V
Maximum Horse Power Rating
15 hp 380...480 V
Complementary
Line current
25.6 A 500 V 3 phase 11 kW / 15 hp
36.6 A 380 V 3 phase 11 kW / 15 hp
Apparent power
31.7 kVA 500 V 3 phase 15 kW / 20 hp
Prospective line Isc
22 kA 3 phase
Nominal output current
27.7 A 4 kHz 500 V 11 kW / 15 hp
Maximum transient current
41.6 A 60 s 11 kW / 15 hp
Output frequency
0.0005…0.599 kHz
Nominal switching frequency
4 kHz
Switching frequency
2...16 kHz adjustable
Speed range
1…100 asynchronous motor in open-loop mode
Speed accuracy
+/- 10 % of nominal slip 0.2 Tn to Tn
Torque accuracy
+/- 15 %
Transient overtorque
170…200 %
Braking torque
<= 170 % with braking resistor
Asynchronous motor control profile
Flux vector control without sensor, standard
Voltage/frequency ratio, 5 points
Voltage/frequency ratio, 2 points
Voltage/frequency ratio - Energy Saving, quadratic U/f
Flux vector control without sensor - Energy Saving, NoLoad law
Synchronous motor control profile
Vector control without sensor
Regulation loop
Adjustable PID regulator
Motor slip compensation
Adjustable 0...300 %
Automatic whatever the load
Not available in voltage/frequency ratio (2 or 5 points)
Local signalling
1 LED red drive voltage
1 LED green CANopen run
1 LED red CANopen error
1 LED red drive fault
Output voltage
<= power supply voltage
Noise level
43 dB 86/188/EEC
insulation
Electrical between power and control
Electrical connection
Screw terminal 0.5...1.5 mm², AWG 18...AWG 14 control)
Removable screw terminals 6...16 mm², AWG 8...AWG 6 motor/braking resistor)
Screw terminal 10...16 mm², AWG 8...AWG 6 power supply)
Tightening torque
4.43 lbf.in (0.5 N.m), 4.4 lb/ft control)
10.62 lbf.in (1.2 N.m), 10.6 lb/ft motor/braking resistor)
10.62 lbf.in (1.2 N.m), 10.6 lb/ft power supply)
Supply
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 mA overload and short-circuit protection
Analogue input number
3
Analogue input type
AI1 voltage 0...10 V DC 30000 Ohm 10 bits
AI2 bipolar differential voltage +/- 10 V DC 30000 Ohm 10 bits
AI3 current 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration) 250 Ohm 10 bits
Sampling duration
2 ms AI1, AI2, AI3) - analog
2 ms AO1) - analog
Response time
LI1...LI6 8 ms +/- 0.7 ms logic
R1A, R1B, R1C 2 ms relay
R2A, R2C 2 ms relay
Accuracy
+/- 0.2 % AI1, AI2, AI3) for a temperature of -10...60 °C
+/- 0.5 % AI1, AI2, AI3) for a temperature of 25 °C
+/- 1 % AO1) for a temperature of 25 °C
+/- 2 % AO1) for a temperature of -10...60 °C
Linearity error
+/- 0.2...0.5 % of maximum value AI1, AI2, AI3)
+/- 0.3 % AO1)
Analogue output number
1
Analogue output type
AO1 software-configurable current 0...20 mA 800 Ohm 10 bits
AO1 software-configurable voltage 0...10 V 470 Ohm 10 bits
Discrete output number
3
Discrete output type
Configurable relay logic R1A, R1B, R1C) NO/NC - 100000 cycles
Configurable relay logic R2A, R2B) NO - 100000 cycles
Logic LO)
Minimum switching current
5 mA 24 V DC configurable relay logic
Maximum switching current
R1 3 A 250 V AC resistive, cos phi = 1
R1 4 A 30 V DC resistive, cos phi = 1
R1, R2 2 A 250 V AC inductive, cos phi = 0.4
R1, R2 2 A 30 V DC inductive, cos phi = 0.4
R2 5 A 250 V AC resistive, cos phi = 1
R2 5 A 30 V DC resistive, cos phi = 1
Discrete input number
7
Discrete input type
Programmable (sink/source) LI1...LI4)24...30 V DC level 1 PLC
Programmable as pulse input 20 kpps LI5)24...30 V DC level 1 PLC
Switch-configurable PTC probe LI6)24...30 V DC
Safe torque off STO)24...30 V DC - 1500 Ohm
Discrete input logic
Negative logic (sink) LI1...LI6), > 19 V, < 13 V
Positive logic (source) LI1...LI6), < 5 V, > 11 V
Acceleration and deceleration ramps
CUS
Deceleration ramp adaptation
Linear
Deceleration ramp automatic stop DC injection
S
Ramp switching
U
Braking to standstill
By DC injection
Protection type
Input phase breaks drive
Overcurrent between output phases and earth drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection drive
Communication Port Protocol
CANopen
Modbus
Connector type
1 RJ45 on front face)Modbus/CANopen
Physical interface
2-wire RS 485 Modbus
Transmission frame
RTU Modbus
Type of polarization
No impedance Modbus
Number of addresses
1…127 CANopen
1…247 Modbus
Method of access
Slave CANopen
Electromagnetic compatibility
1.2/50 µs - 8/20 µs surge immunity test, level 3 IEC 61000-4-5
Conducted radio-frequency immunity test, level 3 IEC 61000-4-6
Electrical fast transient/burst immunity test, level 4 IEC 61000-4-4
Electrostatic discharge immunity test, level 3 IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test, level 3 IEC 61000-4-3
Voltage dips and interruptions immunity test IEC 61000-4-11
Width
7.09 in (180 mm)
Height
15.91 in (404 mm)
Depth
9.13 in (232 mm)
Product Weight
19.18 lb(US) (8.7 kg)
Option card
Communication card CANopen daisy chain
Communication card CANopen open style
Communication card DeviceNet
Communication card EtherNet/IP
Communication card Profibus DP V1
Functionality
Mid
Specific application
Other applications
Environment
Standards
EN/IEC 61800-3
EN/IEC 61800-5-1
EN 55011 class A group 1
EN 61800-3 environments 1 category C2
EN 61800-3 environments 2 category C2
Product Certifications
CSA
GOST
UL
C-tick
NOM 117
marking
CE
Pollution degree
2 EN/IEC 61800-5-1
IP degree of protection
IP20 EN/IEC 61800-5-1
Vibration resistance
1 gn 13…200 Hz) EN/IEC 60068-2-6
1.5 mm peak to peak 3…13 Hz) EN/IEC 60068-2-6
Shock resistance
15 gn 11 msEN/IEC 60068-2-27
Relative humidity
5…95 % without condensation IEC 60068-2-3
5…95 % without dripping water IEC 60068-2-3
Ambient air temperature for operation
14…122 °F (-10…50 °C) without derating
122…140 °F (50…60 °C) with derating factor
Ambient Air Temperature for Storage
-13…158 °F (-25…70 °C)
Operating altitude
<= 3280.84 ft (1000 m) without derating
3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m
Operating position
Vertical +/- 10 degree
Ordering and shipping details
Category
22153-ATV320/ATV312/ATV32 (10 THRU 30HP)
Discount Schedule
CP4B
GTIN
00785901675518
Returnability
No
Country of origin
ID
Contractual warranty
Warranty
18 months

OTHER SUPERIOR PRODUCTS

This Altivar 32 3-phase variable speed drive has a rated power of 11kW, and a supply voltage of 380V to 500V AC. It is designed for applications such as small conveyors, hoists, bagging / labeling machines, mixers, kneaders, textile machines, pumps, compressors, fans, wood-working and metal processing machines. It has a 180mm-wide compact form-factor, allowing for a flexible and easy installation on a mounting plate without any space between adjacent drives. It also offers a snap-lock seal, status and faults display, a jog dial navigation button and an integrated EMC filter. It offers high readability of key parameters thanks to a bright LED 4-digit display. SoMove software compatibility enables saving and transfering of configurations to spare drive, reducing maintenance downtime.

FAQ

Q1. What about the lead time?

A: 3-5 days for Sample preparing ,8-10 working days for mass production.

Q2. Do you have any MOQ limit of Industrial Servo Drives?

A: Low MOQ, 1pc is available.

Q3. How do you ship the goods and how long does it take to arrive?

A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.

Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.