| Inverter Ratings |
| Collector-Emitter Voltage (VCES) | | | | 600 | V |
| Output Phase Current (IC) | TC=25C, TJ<150C | | | 5 | A |
| Output Phase Current (IC) | TC=100C, TJ<150C | | | 3 | A |
| Output Peak Phase Current (IPK) | TC=25C, <1ms pulse | | | 10 | A |
| Short Circuit Withstand Time (tSC) | VPN400V, TJ=150C, VD=15V | | | 5 | s |
| Collector Dissipation (PC) | TC=25C, per chip | | | 18.9 | W |
| Operating Junction Temperature (TJ) | | -40 | | 150 | C |
| Control (Protection) Ratings |
| Control Supply Voltage (VD) | Applied between VD(H)-COM, VD(L)-COM | | | 25 | V |
| High-Side Control Bias Voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | | | 25 | V |
| Input Voltage (VIN) | Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), IN(WL) - COM | | VD0.5 | | V |
| Total System Ratings |
| Self Protection Supply Voltage Limit (VPN(PROT)) | VD=13.5-16.5V, Inverter part TJ=150C, Non-repetitive, <2s | | | 400 | V |
| Module Case Operation Temperature (TC) | | -30 | | 125 | C |
| Storage Temperature (TSTG) | | -40 | | 150 | C |
| Isolation Voltage (VISO) | 60Hz, sinusoidal, AC 1min, between all pins and heat sink | | | 2000 | Vrms |
| Thermal Resistance |
| Junction to Case (Rth(j-c)Q) | Inverter IGBT (per 1/6 module) | | | 6.6 | K/W |
| Junction to Case (Rth(j-c)F) | Inverter FWD (per 1/6 module) | | | 8.5 | K/W |
| Electrical Characteristics (TJ = 25C, unless otherwise specified) |
| Collector-Emitter Saturation Voltage (VCE(SAT)) | VD=VDB=15V, VIN=5V, IC=2.5A, TJ=25C | | 1.48 | 1.85 | V |
| Collector-Emitter Saturation Voltage (VCE(SAT)) | VD=VDB=15V, VIN=5V, IC=2.5A, TJ=125C | | 1.69 | - | V |
| FWD Forward Voltage (VF) | VIN=0, IF=2.5A, TJ=25C | | 1.75 | 2.15 | V |
| Short-Circuit Trip Level (VSC(ref)) | VD=15V (2) | | 0.48 | 0.51 | V |
| Supply Circuit Under-Voltage Protection Trip Level (UVDT) | | 10.3 | 11.4 | 12.5 | V |
| Over-Temperature Protection (OTT) | Detect LVIC Temperature Trip Level | 110 | 130 | 150 | C |
| Fault Output Voltage (VFOH) | VSC=0V, VFO Circuit: 10k to 5V pull-up | 4.9 | - | - | V |
| Fault Output Voltage (VFOL) | VSC=1V, VFO Circuit: 10k to 5V pull-up | - | - | 0.5 | V |
| Fault Output Pulse Width (tFO) | | 20 | - | - | s |
| ON Threshold Voltage (Vth(on)) | Applied between IN pins COM | 2.3 | 2.6 | - | V |
| OFF Threshold Voltage (Vth(off)) | Applied between IN pins COM | | 0.8 | 1.2 | V |
| Bootstrap Diode Forward Voltage (VF(BSD)) | IF=10mA Including Voltage Drop by Limiting Resistor (6) | | 1.0 | 2.0 | V |
| Built-in Limiting Resistance (RBSD) | Included in Bootstrap Diode | 80 | 100 | 120 | |
| Recommended Operation Conditions |
| Supply Voltage (VPN) | Applied between P-NU, NV, NW | 0 | 300 | 400 | V |
| Control Supply Voltage (VD) | Applied between VD(H) COM, VD(L) - COM | 13.5 | 15.0 | 16.5 | V |
| High-Side Bias Voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | 13.5 | 15.0 | 18.5 | V |
| Arm Shoot-Through Blocking Time (tded) | For each input signal | 1.0 | - | - | s |
| PWM Input Frequency (fPWM) | -40C < TJ < 150C | - | - | 20 | kHz |