Running a small bakery or a busy café pass, and outgrowing your 3-tray countertop oven — but with no room (and no three-phase power) for a full-size 10-tray deck? That is exactly the gap the CK60C was built to fill.
It is a true commercial convection oven: five trays in a single load, forced hot-air circulation, 0–300°C range, and 48 recipes stored on a touchscreen so a new starter can pull the same bake as your head baker. The whole machine sits in a 640 × 770 × 640 mm footprint — about the size of a under-counter fridge — and runs on ordinary 220V single-phase power at 3.5kW.
Who This Oven Is Built For
1.Opening a first bakery or neighbourhood boulangerie
5 trays covers 150–300 pastries or 200+ buns per batch without the capex and 380V rewiring a 10-tray unit demands
2.Running a café / coffee shop with an in-house pastry case
Bake the morning muffin-and-croissant run in two loads before opening; the 48-menu memory means one tap, no recipe cards
3.A restaurant or hotel kitchen doing roasts, gratins and reheating
0–300°C handles low-and-slow roast through to high-heat finish; convection replaces a shelf of single-purpose kit
4.A home baker turning professional / private studio
Commercial-grade duty cycle in a machine that fits a 1 m² corner and a residential-style 220V line
5.A catering or events operator on mobile setups
Compact body, no gas certificate, no flue — plug in, prove the menu, move on
The Five Questions Every Buyer Asks Before Ordering
1."Will my current trays fit?"
Check this first — it's the #1 reason convection ovens get returned.
The CK60C takes 435 × 315 mm trays, five supplied. That is a narrower, purpose-built format (not the 600×400 mm bakery standard, and not GN 1/1 gastronorm). The pay-off is a slimmer 640 mm body that slides into tight bench runs. If your racks are 60×40, ask us about the CK-series wide-body alternative before you buy — send a photo of your existing tray and we'll confirm the fit in one reply. Trays and spares are always in stock from the factory.
2."Do I need three-phase power installed?"
No — and that usually saves you the single biggest hidden cost in an oven fit-out.
Rated 220V / 3.5kW / single-phase, the CK60C draws roughly 16A. That is within reach of a normal small-shop supply, so most cafés avoid a 380V upgrade, a new sub-board and the electrician's call-out that a 6–9kW full-size unit forces on you.
Two things to confirm with your local sparky first: 3.5kW sits close to the top of what a 16A circuit can carry continuously, so plan a dedicated line with its own breaker (≥2.5mm² cable, C20 breaker is the usual spec) rather than sharing the espresso machine circuit. And tell us your voltage, frequency and plug type — 220V/50Hz, 230V/50Hz and 60Hz regions get built to order.
3."Will the top tray brown like the bottom one?"
That's the whole job of convection, and it's why we spec 65 mm tray pitch rather than squeezing in a sixth shelf. Even spacing = clean airflow over every tray, so cookies on shelf 5 colour the same as shelf 1 and you stop rotating pans mid-bake. Full 5-tray loads, not "5 trays but really only 3 usable".
4."How does 48-menu memory actually change my day?"
Program temperature, time and fan stage once — croissant 175°C / 16 min, chicken thigh 200°C / 28 min, sheep's milk cheese 220°C / 6 min — save it under a name, and any shift anywhere just taps the icon. No dials to mis-set, no "who turned it up to 210 again?", no manager rewriting par sheets. 48 slots is enough for a full pastry case and the savoury menu and your seasonal specials.
The touchscreen is the other half of it: icon-driven, glove-friendly, and new staff are productive in about ten minutes instead of a two-week shadow.
5."Is 0–300°C genuinely useful, or a spec-sheet number?"
Both ends earn their keep. Low end holds proof-adjacent warmth, dehydration and slow roast; the 150–250°C band does the vast majority of baking; 300°C is there for pizza, flatbread, blistered veg and the last-minute glaze-and-crisp. One cavity, no switching appliances.
Why Buy Direct From the Manufacturer
1.Factory, not a trading floor. We build baking equipment in Guangzhou and hold the CK-series on the line — sample units usually ship in 5–15 days, not the 60–90 a distributor quotes.
2.Built to your socket. Voltage, frequency, plug and body colour are specified before production, not "adapted" after delivery.
3.Parts that actually fail, in stock. Fan motor, heating element, door gasket, control board — dispatched within days, so a fault never costs you a week of trade.
4.Documentation support. Manuals in EN/Chinese/RU; CE/other certification available subject to your destination market — tell us the country and we'll confirm what ships with the unit.
5.Flexible MOQ. One unit for a trial, container pricing for rollouts. T/T, L/C, WU, D/P accepted.