MachineU > China Products > Rubber & Plastics > Rubber Raw Materials > Silicone Rubber
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Specifications
Brand Name :
CHENGUANG FSP
Model Number :
R-890
Certification :
ISO / SGS
Place of Origin :
China
Product Name :
Silicone Encapsulant
Material :
Two-component Silicone Rubber
Appearance :
Transparent elastomer
Properties :
Cured / Uncured
Characteristics :
Vulcanization at room temperature in any thickness, can be heat accelerated
Application :
Cable connectors encapsulating
Description

Silicone Encapsulant
Two Component Transparent Elastomer Silicone Encapsulant Applying to Potting and Sealing


Description

Room Temperature Curable, Addition-curing Two-component Silicone Rubber.


Characteristics:

  • Very low viscosity, good fluidity.
  • Vulcanization at room temperature in any thickness, can be heat accelerated.
  • Insulator and moisture-proof, resistance of high and low temperature.
  • Transparent elastomer, repairable.
  • Good adhesion to substrates ,no corrosioned primer.

Typical Properties

Properties Test Method Unit Value
Uncured Componet A B
Appearance Visual
Transparent Liquid
 Transparent
Specific gravity, 23℃ GB/T 1033.1-2008 g/cm3 0.98 0.98
Viscosity,after stirred at 23℃ GB/T 2794-1995 mPa.s 500-800 500-800
Mixing ratio A:B 1:1
Pot life, 25℃ h 1
Cured Penetration GB/T 269-1991 200-300
Dielectric strength GB/T 1408.1-2006
MV/m
 ≥15
Dielectric constant, 1MHz
GB/T 1693-2007
 ≤2.8
Volume resistivity GB/T 1410-2006 Ω.cm ≥1.0×1013

These figures are only intended as a guide and should not be used in preparing specifications.

How to use

1. Weight: According to 1:1 weight ratio to take A and B components.

2. Mixing: It is better to use specialized equipment for fully mixing, such as small planetary mixer. Pay attention to scratch bottom and wall of container when stir by manual operation.

3. Pouring: Pour the mixed rubber into encapsulating site. Settle stilly 8～10hours to let it cure at room temperature naturally. Heat can accelerate curing.

4. Deaeration: Fast curing when necessary, should guarantee no air bubbles in the curing rubber(The mixed rubber settle stilly 10-30 minutes at room temperature is OK). Or place the mixture together with its container should in vacuum degassing tank to be degassed. The mixture surface location will rise to 3~4 times higher than original and automatically break bubbles to collapse. Please hold vacuum status more 4~6 minutes, then release.

Packing, Storage & Shipping

R-890 A/B is supplied in 2×20Kg plastic drum, net weight.

R-890 A/B has a shelf life of 6 months at least if stored in the sealed original container between 0℃ to 30℃.

Storage time beyond the specified data does not mean that the product is no longer usable. In which case, the properties required for the intended use must be checked for quality assurance reasons.
There is no shipping limitation for R-890.

Compatibility

Certain materials, chemicals, curing agents and plasticizers can inhibit the cure of R-890. Most notable of these include:

- Compounds such as organotin and other organometallic compounds
- Silicone rubber that contains an organotin catalyst
- Materials that contain sulfur, polysulfides, polysulfones, or other sulfur-based compounds
- Materials that contain amines, urethanes, or other amine-based compounds
- Plasticizers that contain unsaturated hydrocarbons
- Certain residues from solder flux

If a substrate or material is questionable with respect to potentially causing inhibition of cure, it is recommended that a small scale compatibility test be run to ascertain suitability in a given application. The presence of liquid or uncured product at the interface between the questionable substrate and the cured gel indicates incompatibility and inhibition of cure.

Attention

As components of group A and group B have been confirmed without toxic and aggressive substances over past years, no need special preventive measure, only requests to use the general industrial health standard.
R-890 should avoid contacting with nitrogen, phosphorus, sulfur compound and organic tin or other heavy metal compound because of being easy to be inactivated. The containers should be keeping clean.
Temperature will impact pot life of mixed R-890, the higher temperature, the shorter pot life.
Limited Warranty Information

Although the data presented in this leaflet align with our current knowledge, the user must still inspect all supplies upon receipt. We reserve the right to modify product specifications based on technological advancements or new developments. Due to the uncontrollable processing conditions, particularly when incorporating raw materials from other companies, it is recommended to conduct preliminary trials to verify the suggestions provided in this leaflet. These recommendations do not exempt the user from investigating the possibility of infringing on third-party rights and, if necessary, clarifying their position. The recommendations for product use do not imply any warranty, whether expressed or implied, regarding the fitness or suitability of the product for a specific purpose.

Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting SealingTransparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing

Send your message to this supplier
Send Now

Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing

Ask Latest Price
Product Detail
Brand Name :
CHENGUANG FSP
Model Number :
R-890
Certification :
ISO / SGS
Place of Origin :
China
Product Name :
Silicone Encapsulant
Material :
Two-component Silicone Rubber
Contact Supplier
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing
Transparent Elastomer Silicone Encapsulant 2 Component Silicone Rubber For Potting Sealing

Chenguang Fluoro & Silicone Polymer Co.,Ltd

Active Member
3 Years
chengdu
Since 2002
Business Type :
Manufacturer, Distributor/Wholesaler, Agent, Importer, Exporter, Trading Company, Seller, Other
Main Products :
Elastomer Silicone, Silicone Molding Material, MVQ Silicone
Total Annual :
4950000-5000000
Employee Number :
10~20
Certification Level :
Active Member
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products Elastomer Silicone
MachineU China Products Rubber & Plastics Rubber Raw Materials Silicone Rubber
Contact Supplier
Submit Requirement