MachineU > China Products > Rubber & Plastics > Rubber Raw Materials > Silicone Rubber
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Specifications
Brand Name :
CHENGUANG FSP
Model Number :
R-1400M
Certification :
ISO / SGS
Place of Origin :
China
Product Name :
Precision Mold Making Silicone Rubber
Color :
White
Tensile Strength :
2.0Mpa
Elongation at Break :
300%
Tear Strength :
8kN/m
Hardness :
30-40 Shore A
Description

Precision Mold Making Silicone Rubber

Description

Room Temperature Curable, Addition-curing Two-component Silicone Rubber.


Characteristics:

  • Good fluidity
  • Low shrinkage
  • Good dimensional stability

Application:

  • Resin Matrix Composite mold take shape.
  • Production of precision mold, such as oil drill, supercharger impeller.

Typical Properties

Properties Test Method Unit R-1400M
Uncured Appearance Visual A White
B
Viscosity, after stirred at 23°C GB/T 2794-1995 mPa.s 7×104
Mixing ratio A:B 100:5
Pot life, 25°C h 1
Cured Tensile strength GB/T 528-2009 MPa 2.0
Elongation at break GB/T 528-2009 % 300
Tear strength GB/T 529-2008 kN/m 8
Hardness, Shore A GB/T 531-1999 30-40
Linear shrinkage % 0.5
Coefficient of thermal expansion 1/℃

These figures are only intended as a guide and should not be used in preparing specifications.

How to use

1. Weight: According to weight ratio to take rubber base and curing agent. The amount of curing agent will decide pot life longer or shorter, and the final performance of the vulcanizate will also correspondingly change.

2. Mixing: Fully mix two components, pay attention to scratch bottom and wall of container.

3. Deaeration:The mixture together with its container should be placed in vacuum degassing tank to be degassed in order to guarantee no air bubbles in the curing rubber. The mixture surface location will rise to 3~4 times higher than original and automatically break bubbles to collapse.
Please hold vacuum status more 4~6 minutes, then release.

4. Pouring: Pour the mixed rubber by manual or mechanical operation. And it is better to do vacuum degassing again after it.

5. Curing: The curing time is 24hours at 25℃. Additional vulcanization of other 1 hour at 100℃ and 1 hour at 200℃ is needed before use.

Packing, Storage & Shipping

Rubber base is supplied in 20kg plastic drum, net weight. The curing agent separate used plastic bottle or drum.

Please store the product in cool and dry place avoiding contact with acid, alkali, metal organic salt etc. The rubber base and
the curing agent have a shelf life of 6 months at least if stored in the sealed original container.
There is no shipping limitation.

Attention

After each use, curing agent must be tightly covered with cap to avoid inactivation
resulted from a long time exposed in the air. The presence of a large amount of sediment indicates this curing agent out of service. It
is recommended to divide the curing agent into vials for frequent use.
The curing agent contains tetraethoxy-silane, is flammable (flash point 40.6℃) and may cause irritation in contact with the eyes and skin. Adequate protective measures are required.
Limited Warranty Information

The data presented in this leaflet are in accordance with the present state of our knowledge, but do not absolve the user from
carefully checking all supplies immediately on receipt. We reserve the right to alter product constants within the scope of technical progress or new developments.
The recommendations made in this leaflet should be checked by preliminary trials because of conditions during processing over which we have no control, especially where other companies’ raw materials are also being used. The recommendations do not absolve the user from the obligation of investigating the possibility of infringement of third parties’ right and, if necessary, clarifying the position, recommendations for

use do not constitute a warranty, either express or implied, of the fitness or suitability of the products for a particular purpose.

Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil DrillLow Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill

Send your message to this supplier
Send Now

Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill

Ask Latest Price
Product Detail
Brand Name :
CHENGUANG FSP
Model Number :
R-1400M
Certification :
ISO / SGS
Place of Origin :
China
Product Name :
Precision Mold Making Silicone Rubber
Color :
White
Contact Supplier
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill
Low Shrinkage White Liquid Silicone For Mold Making 300% Elongation For Oil Drill

Chenguang Fluoro & Silicone Polymer Co.,Ltd

Active Member
3 Years
chengdu
Since 2002
Business Type :
Manufacturer, Distributor/Wholesaler, Agent, Importer, Exporter, Trading Company, Seller, Other
Main Products :
Elastomer Silicone, Silicone Molding Material, MVQ Silicone
Total Annual :
4950000-5000000
Employee Number :
10~20
Certification Level :
Active Member
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products Elastomer Silicone
MachineU China Products Rubber & Plastics Rubber Raw Materials Silicone Rubber
Contact Supplier
Submit Requirement