MachineU > China Products > Electrical Equipment & Supplies
Tested RF Coaxial Connector MyAntenna A-IPEX1-1.25A Meeting Strict Electrical Mechanical Requirements
Tested RF Coaxial Connector MyAntenna A-IPEX1-1.25A Meeting Strict Electrical Mechanical Requirements
Specifications
Number of Ports :
1
Interface :
内针
RF Series :
IPEX
Connector Type :
板端
Frequency :
6GHz
Impedance :
50Ω
Interface Diameter :
2mm
Description :
Connector Receptacle IPEX Male Pin 50Ω Surface Mount
Mfr. Part # :
A-IPEX1-1.25A
Package :
SMD
Model Number :
A-IPEX1-1.25A
Description

Product Overview

This product specification defines the product performance and the test methods to ascertain the performance of the RF coaxial connector, which is designed and manufactured by TREASURE ADVANCE ENTERPRISES LIMITED. This RF coaxial connector is designed to meet electrical, mechanical, and environmental performance requirements.

Product Attributes

  • Brand: TREASURE ADVANCE ENTERPRISES LIMITED
  • Certifications: UL498 (Standard for safety of attachment plug and receptacle)
  • Harmful Material Control: Follows ROSH directive requirements.
  • Marking: Manufacturers name, industry recognized logo, or customer approved marks. Green cresset is the mark of lead free processing.

Technical Specifications

ItemRequirementsTest Methods
1. Examination of ProductProduct shall be conforming to the requirements of applicable product drawing.Visually, dimensions and functionally inspected per applicable product drawing.
2. Contact Resistance (Low Level)20 m Max. initialSubject mated contacts assembled in housing to closed circuit of 10 mA max. at open circuit voltage of 20 mV max.
3. Insulation Resistance500 M Min.Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connector. MIL-STD-202, Method 302, Condition B (100 V DC10%).
4. Dielectric StrengthConnector must withstand test potential of 100 VAC for 1 minute.Current leakage must be 0.5 mA max..Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connector. MIL-STD-202, Method 301.
5. Unmating ForceTotal unmate force: Initial 5N min. after 30 cycles 3Nmin.Unmate the receptacle at a speed 253mm/m by the push-on/pull-off machine
6. Durability (Repeated Mating/Unmating)Contact Resistance: 30m Max. after testingMate and unmate connector for 30 cycle.
7. Crimp strength10N minPull the cable as shown at a speed 253mm/m by tensile strength machine.
8. Vibration Sinusoidal Low FrequencyNo electrical discontinuity greater then 1 sec (s) shall occur. Contact resistance:30 m max.Subject mated connector to 10-55-10 Hz traversed in 1 minute at 1.5 mm amplitude 2 hours each of 3 mutually perpendicular plane, 10 mA applied MIL-STD-202, Method 201.
9. Thermal shockNo damage, Contact Resistance (Low Level) (Final) 30 m max.Temperature range from -55C to +85C .Start from -55C,after 30 min. change to +85C;change time is no more than 30 seconds. Total 5 cycles. MIL-STD-202, Method 107D,condition A.
10. HumidityNo damage, Contact Resistance (Low Level) (Final) 30 m max.. Dielectric Strength should be OK, Insulation Resistance should be 200 M min.Temperature :402C 96 hours. Relative Humidity : 90-95%; Duration :96 Hours. MIL-STD-202, Method 103.
11. Salt SprayContact Resistance (Low Level) (Final)100 mmax.51% salt concentration 484 hours 352C MIL-STD-202, Method 101 Condition B.
12. High temperatureContact resistance: 100 mmax.Subject product to 852C for 96 hours continuously. MIL-STD-202, Method 108.
13. VSWR1.3max. at 0.1GHz~3GHz; 1.5max. at 3GHz~6GHzMeasure the VSWR as shown by the network,analyzerFrequency:100MHz~6GHz
Test DescriptionTest Sequence ATest Sequence BTest Sequence CTest Sequence DTest Sequence ETest Sequence FTest Sequence GTest Sequence HTest Sequence ITest Sequence JTest Sequence K
1. Examination of Product1,31,31,51,51,51,51,91,91.41.71.3
2. Contact Resistance (Low Level)22,42,42,42.42.82.82.52.5
3. Insulation Resistance3,63,63,6
4. Dielectric Strength4,74,7
5. Unmating Force2
6. Durability3
7. Crimp strength32
8. Vibration Sinusoidal Low Frequency3
9. Thermal shock35
10. Humidity5
11. Salt Spray3
12. High temperature4
13. VSWR

2410121459_MyAntenna-A-IPEX1-1-25A_C22467595.pdf

Send your message to this supplier
Send Now

Tested RF Coaxial Connector MyAntenna A-IPEX1-1.25A Meeting Strict Electrical Mechanical Requirements

Ask Latest Price
Product Detail
Number of Ports :
1
Interface :
内针
RF Series :
IPEX
Connector Type :
板端
Frequency :
6GHz
Impedance :
50Ω
Contact Supplier
Tested RF Coaxial Connector MyAntenna A-IPEX1-1.25A Meeting Strict Electrical Mechanical Requirements

Shenzhen ECER Network Technology Co., Ltd.

Verified Supplier
1 Years
anhui, shenzhen
Since 2009
Business Type :
Manufacturer, Distributor/Wholesaler, Agent, Importer
Main Products :
FFC FPC Connector, Memory Connectors, Power Connectors
Total Annual :
10000000-50000000
Employee Number :
300~500
Certification Level :
Verified Supplier
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products Coaxial Connector (RF) Assemblies
MachineU China Products Electrical Equipment & Supplies
Contact Supplier
Submit Requirement