Oil Treatment Complete Engine Sealant Boost Engine Efficiency And Prevent Damage

Function:

Adding this product can form a solid repair film on all friction surfaces of the engine. This can effectively repair and reduce engine wear, restore the sealing of the engine cylinder liner and piston rings, and significantly improve engine power. It eliminates phenomena such as burning oil, emitting black smoke, and high oil consumption, and reduces friction and anti-wear, which can effectively prevent the engine from "dry grinding" during cold starts in winter and "semi-dry grinding" caused by high temperatures or oil deterioration in summer.

Product Advantages:

• Repair and reduce engine wear
  The product can form a stable repair film on the friction surface of the engine, effectively repair and reduce the wear of the engine, and help restore the operating efficiency of the engine.
• Restore tightness and boost power It helps restore the tightness of the engine liner to the piston ring, which significantly improves the engine's dynamics and makes the engine run more smoothly and powerfully.
• Eliminate the problem of burning engine oil and black smoke This product can effectively eliminate the problems of engine oil burning, black smoke, excessive fuel consumption, etc., reduce pollutant emissions, and improve fuel efficiency..
• Effectively prevent the phenomenon of "dry grinding" and "semi-dry grinding".
  In the case of cold start in winter, it can effectively prevent the occurrence of "dry grinding" phenomenon and protect the internal parts of the engine.
  In the case of high temperature or oil deterioration and failure in summer, it can effectively prevent the phenomenon of "semi-dry grinding" and protect the long-term operation of the engine.
• Wear reduction and anti-wear, prolong the service life of the engine The product has a wear and anti-wear effect, helping to reduce friction inside the engine and reduce wear, thereby extending the life and reliability of the engine.
• Adapts to extreme temperature conditions The product can still function effectively in extreme temperature conditions, whether it is low temperature starting or high temperature operation, it can provide effective protection for the engine.

Operation Specifications:

1. Preparation:
   Clean the engine oil passages: Before use, make sure the engine oil passages are not severely blocked. It's a good idea to change the oil filter and check the oil level to make sure the engine is in working order.
2. Add Products:
   Add to engine oil: Add the appropriate amount of engine repair agent to the engine oil filler. Typically, the product will give a percentage of the addition based on the amount of oil in the engine or the oil capacity. Please refer to the product manual for the specific ratio.
   Start the engine: After adding the repair agent, start the engine and idle for about 5-10 minutes to let the product evenly mix into the engine oil system to ensure that the friction parts are fully in contact with the repair film.
3. Post-operation checks: Check the quality of the oil: After the operation, check the quality of the oil to ensure that the engine is running smoothly and there is no abnormal noise or oil leakage.
4. Long-term effects: For best results, it is recommended to use this product regularly, especially in cases of high and low temperatures, or in the case of aging engines. Refill or reuse according to the recommended use cycle in the instructions.

Notices:

• Proportional use:
  Please add an appropriate amount of repair agent according to the oil quantity or oil capacity of the engine in strict accordance with the product instructions to avoid excessive use.

• Avoid over-adding:
  Avoid adding too much repair agent, too much may cause the lubricant to thicken too much or affect the normal operation of the engine.
• Engines for clean oil:
  This product is recommended for use in engines with clean oil and no severe wear. If there is serious mechanical damage or malfunction to the engine, it should be professionally inspected and repaired first.
• Check the engine status regularly:
  Once added, it is advisable to regularly check the working condition of the engine, including oil quality, engine temperature, and noise. If there is an abnormality, it should be stopped immediately for inspection.
• Storage conditions:
  Store the product in a dry, cool place and avoid exposure to high temperatures or direct sunlight. Keep caps tightly closed and out of reach of children.
• Security Protection:
  When using, it is best to wear gloves and glasses and avoid direct contact with the skin or eyes. In case of accidental contact, rinse immediately with plenty of water.
• Pay attention to the environment:
  Empty bottles should be properly disposed of after use and should not be discarded at will. Dispose of waste in accordance with local environmental regulations.